Right now on the forums we are allowing external linking to non-secure content. With the recent change in security policy for most of the major browsers, I will be switching this functionality off. This means that any links to external images that are not served via a secure (HTTPS) method will appear as a broken link. Eventually this will apply to the rest ofthe websites in the LDraw ecosystem.

Philo's question on naming a strange shaped part reminded me on one open question.

These nexo Knight parts have an area that is notable rough. With a relief that is much more visible than e.g. Slopes (may be a bad comparison)
However within the LDD files, those details. are not there.

I did one part with those details, 27257 that I have attached here. What do you think, should this be modeled or not?

My approach was to have one of the bumps as a submodel (hexagonal pyramid with condlines), the coloured areas are inlined as they intersect.

   
   

Hi
Is there anywhere an LDCad tutorial in german aviable?
Is it planned to translate the program in German?
I know english is a world wide language, but my mother tongue is german and so it's for my easier.

Regards Johann

Hi folks,

As outlined here:

https://forums.ldraw.org/thread-22653.html

nominations for the 2018/2019 LDraw.org Steering Committee election will close at 11:59 PM GMT on 28 February 2018 and elections will start on 01.03.2018. Only those candidates who have been nominated, seconded, and have accepted as outlined, will be eligible for election. So if you are a candidate that has not yet accepted or declined, please consider deciding. The list with the candidates as well as their status can be found here:

https://forums.ldraw.org/thread-22706.html

If you feel your favourite nominee is missing on the list please use the link above to nominate him/her.

Willy Tschager
On behalf of the LDraw.org Steering Committee

Following up on the discussion on MLCad 3.50 which led to discussing snap meta in LDCad here is something I found.

I see that part 85984 (better known as cheese slope 1x2) misses snap meta at underside so it won't snap at a 90 degree angle on say a 1x2 brick with studs on side.
I cannot remember having problems with that part, but now it does not snap.
I see part 85985 is not made with the subpart without top face that is used for patterned versions of this slope.
The the patterned variants of 85985 use 85985s01 which has the snap meta.
Shouldn't part 85984 be fixed and make use of the 85985s01 too?

An updated version of the LDraw All-In-One-Installer, in short AIOI, has been released.

The AIOI supports Windows XP (Home and Pro), Windows Vista or higher (all versions). On 64-Bit Operating Systems it will install in the "Program files (x86)" folder. The Installer will NOT run on Windows 95, 98, ME, NT Ver 4, 2000, or XP below SP2.

It contains the following changes:

* Update to Parts Library 2018-01
* Update to MLCad.ini 2018-01
* Update to LDView 4.3
* Update to LPub3D 2.0.20.0.645
* Update to LeoCAD 18.01-10289
* Update to Offline Parts Catalog 2018-01
* Update to LDCad 1.6a
* Update to LICreator 3.2.153

You can download the AIOI from:

Home > Help > Get Started > LDraw All-In-One-Installer

Many thanks to all the programmers who contributed to this release.

Classic Space: LL-924 Variants

   

https://www.flickr.com/photos/veynom/8733161988/

The LEGO Group:
LEGO Bricks in the Making

https://www.youtube.com/watch?v=C3oiy9eekzk

an official documentation about factories and moulding  

Hi there!
  I found these stickers under review: http://www.ldraw.org/cgi-bin/ptdetail.cg...94325a.dat

I'd like to use them, but when I load them in LeoCAD, all I see is a few weird yellow structures, definitely not stickers. :-)

Can please somebody explain how to add stickers to my model?

TIA,
  Alberto

Hi
As the headline says, the instant email notification does not work for me. What can this be?

Regards Johann