Hi all,

I am looking for this one
https://www.bricklink.com/v2/catalog/cat...4#T=C&C=80



Has it been made?

Hi all,

I have a model that has the part 572c01 in it.

LEGO part 14210: String with End Studs and Minifig Grips 21L
Bricklink Item No: 63141
String with End Studs 21L overall with Climbing Grips (16.1cm)
Alternate Item No: 76065, 14210

Is there a template for LDCad for this yet?
If not, can someone make it or tell me how to do that.

In the end, I need this part to go to Stud.io too to make render of the model.
Thanks!

Hi,

Is it possible to get 3813 Minifigure, Utensil Microphone (belville) in LDRAW?.

It's not urgent since I can use a simular part in place of it, it's for a gearbox, and the bar sized part goes inside of the bar hole of a technic knob wheel. I am using 22484 instead but it does not come in black and has no stopper unlike this, which comes in black and cant be pushed too far in .

Thanks, Snipe.

My usual approach placing rings is trail'n'error. I wonder if there is a mathematical way or even a tool which does it for me? I have these cylo:

1 1 50 -37 -10 43.75 0 0 0 0 -43.75 0 10 0 48\2-4cylo.dat
1 1 50 -37 -10 40 0 0 0 0 -40 0 3.125 0 48\2-4cylo.dat
1 1 50 -37 -3.125 40 0 0 0 0 -40 0 3.125 0 48\2-4cylo.dat


and need the external ring.

1 1 50 -37 -3.125 4 0 0 0 0 -4 0 3.125 0 48\1-4rin10.dat

is too large cos the distance is not 4 but 3.75. So ...

w.

Super Heroes sets

Hello everyone,
I'm new here and this is my first post so i hope this is at the right place I've scrolled the forum (it's dense, i have a lot of reading to do !) before writing this.
There's a lot of technical stuff here and i hope i will understand the answer because i'm not highly qualified in this field

Here is something i have noticed lately with the Studio renderer : i used the slope 28192 in my model and when i wanted to get a photo render i imported my mpd file in studio. It was ok, except for the 28192 part which was sitting above its correct position, and in a 90° angle. It was positionned differently than in my model in all three directions indeed.

I got it right by going back in my model and modifying the position of the part with the same translation (that is putting it lower and -90°).

Wondering why it is doing this ?
and if other parts are affected and then it could eventually make Studio renderer difficult to use ? Is it something this community can dosomething about or you would simply recommand i use another renderer ?

Thanks,
Gaelle

Trying to pick up on some patterns I did some time ago and new ones for several dimension sets, first one the base set

71200 - LEGO Dimensions Starter Pack



LDR: 
  71200 - LEGO Dimensions Starter Pack - B.mpd (Size: 219.87 KB / Downloads: 27)
Not fully OMR compliant, only the stickers have been added to the file. Other unofficial parts are on the tracker.


71253 - Story Pack - Fantastic Beasts and Where to Find Them

Hi. I am new to this aspect of the Lego hobby, although I have become familiar with MLCAD. I can't seem to find a part in its latest library, and I also can't find it on BrickLink. It is the companion piece for forklift part 4518a, necessary to attach the forklift to anything. It's apparently a 1x2 hinge plate. Has this part been modeled? If not, will any other part do in my MLCAD project? I'm using the forklift rails in an unconventional way; i.e. I'm not building a forklift. Any assistance is greatly appreciated

Since I can't get set 21054 here in North America until July 1st, I'd love if one of the "Rest of the World" folks would take me a high quality photo or scan of this part:
https://rebrickable.com/parts/3069bpr028...lag-print/

I drew a propeller model, because it's a three blade propeller, so the center of the model is no longer the center of the propeller. Can I rotate a certain angle in stl2dat? What should I do?