It's a Bohrok! ...well, almost

[Santeri Piippo]

Thanks to the hard work of very many LDraw parts authors I have here an actual model of a 8564-1 Lehvak. Though, it seems to be missing a little something.

The Krana and the Krana holder pieces are still not modeled, and are the last Bohrok parts that are in such a state. Anyone got thoughts on how are we going to get the models for the Krana? The Bionicle masks in general seem like a nightmare to model. Perhaps that awesome 3D scanner of Philo's could get the mesh? It seems to have the design ID 42042, though note: there's 8 variants though Peeron only pictures 5 of them.

I still think we should congratulate ourselves, we sure have gotten a lot of parts done! I know the rubber band is also missing though that's because I don't know LSynth-fu.

[Philippe Hurbain]

Agreed, an impressive achievement!

Perhaps that awesome 3D scanner of Philo's could get the mesh?

Well, it has been a while I haven't scanned anything so it would be nice to do it again
...but... my Bionicle collection is highly lacking, and I'm afraid I have none of these masks (I'll check). I should have a few parts like this http://www.bricklink.com/catalogItem.asp?P=kraata4 from Rahkshi. I must also have a Thok and a bunch of loose parts.

Edit: I was overly pessimistic - stay tuned
Edit2: teaser:

I am not happy with the grainy surface (maybe caused by rubber low reflectivity), I hope to be able to smooth out things...

[Santeri Piippo]

That is so amazing! Definitely looking forward to the result.

[Santeri Piippo]

Meanwhile:


This is probably the hardest part I've taken onto modeling yet...

[Philippe Hurbain]

Here is the mesh... I'd be happy if you could complete the work (put the edge lines where needed). Tell me if you need minor shape improvements.

[Santeri Piippo]

Ah, that's very great! Cleaning it up now. I guess I'll model the Krana holder afterwards, then followed by those LDD cleanups..

[Santeri Piippo]

So I'm cleaning it up and just now noticed this:


The one I have at hand doesn't have these recess things..? Are they really on the part you scanned? I'm a bit confused now.

[Philippe Hurbain]

Mmhhh, yes, I have something there but it's not symmetrical and I have another crease in the lower part. imho these are molding problems! I edited out the crease on left ear in the new version (attached). Anyway you'll have to cut in halves...
(edit) sorry for the misplacement in thread!

[Santeri Piippo]

Connector rod done. Now to deal with the edgelines...

[Philippe Hurbain]

Now to deal with the edgelines...

Good luck!

[Michael Heidemann]

It is great to see these models nearly finished. Thanks so much for your effort on the Bionicle Technic parts that are very difficult to get right for LDraw. )))))

[Santeri Piippo]

http://www.ldraw.org/cgi-bin/ptdetail.cg...42042a.dat

[Philippe Hurbain]

A second one... Good luck for cleaning!
   

[Jeff Jones]

even more krana :O

[Rene Rechthaler]

does that lid clip also count as "part"?
http://peeron.com/inv/parts/x349
it clips onto the "ass" (the two parts 41665)
https://library.ldraw.org/official/7980
http://peeron.com/scans/8573-1/26

[Jeff Jones]

does that lid clip also count as "part"?
http://peeron.com/inv/parts/x349
it clips onto the "ass" (the two parts 41665)
https://library.ldraw.org/official/7980
http://peeron.com/scans/8573-1/26

good question..... Maybe? well Probably since the roboriders canister lid is on the tracker and that too is part of the packaging soooooo