Existing Part Edit Requests

[Orion Pobursky]

I checked all the updates, I only find it in its initial release here: LDraw.org Parts Update 2009-02 - Sep 16, 2009

may be still on your HD?

I just checked every backup I have. If it ever existed, it's gone now.

[Orion Pobursky]

Another part used in the Quantum Real Explorer that needs a rework, is the Brick 1 x 1 x 2/3 Round with Bar and Clip Vertical (Part 4735)

Currently the grooves on the part are only edge lines, which make it appear smooth during renders. I have reworked it, added proper grooves and a different clip. The clip needs to be a bit narrower though...





with narrower clip

Mom not a fan of the sharp ridges. The real part is more rounded. Maybe torii instead?

[Travis Cobbs]

Mom not a fan of the sharp ridges. The real part is more rounded. Maybe torii instead?

Since the part is so small, I can't be absolutely sure, but I don't think they are rounded. I think they are rectangular grooves with a flat outside. And using tori for features so small would be serious overkill. I think the walls of the divots are too sloped (should be closer to 90 degrees), resulting in the outer parts being too skinny.

[Gerald Lasser]

Here's a hi-res picture of the part. It'S more a trapezoid shape. I also don't like too sharp edges, but using tori here would give us a LOT of quads...
   

I go ahead with those measurements, the indents will be shallower then as I used 1 LDU in the mock-up vs. 0,5 I get from the picture

[Willy Tschager]

You might check what I did on 71342.dat
Minifig Bugle.

w.

[Philippe Hurbain]

Here's a hi-res picture of the part. It'S more a trapezoid shape. I also don't like too sharp edges, but using tori here would give us a LOT of quads...
I go ahead with those measurements, the indents will be shallower then as I used 1 LDU in the mock-up vs. 0,5 I get from the picture

I'd clearly go with the trapezium method, like s\604547s01.dat with the right ridge scaling. More is pure overkill at this scale.

[Gerald Lasser]

@all, thanks for your opinions, I go ahead with this one


  Ldraw_4735_Final.PNG (Size: 47.16 KB / Downloads: 212)

[Magnus Forsberg]

@all, thanks for your opinions, I go ahead with this one

Isn't this very close to the minifig tool handle?
Spanner, screwdriver, hammer. 6246a-f and 11402a-i
That design is placed in subfiles. Could they be used?

[Gerald Lasser]

Isn't this very close to the minifig tool handle?
Spanner, screwdriver, hammer. 6246a-f and 11402a-i
That design is placed in subfiles. Could they be used?

No, they have one too many groove...
I tried looking them up as well

[Philippe Hurbain]

@all, thanks for your opinions, I go ahead with this one

Imho, bottom of grooves cylis are just wasting triangles (though you caould use a single cyli for whole length...)

[Orion Pobursky]

No, they have one too many groove...
I tried looking them up as well

You could just have one groove as a primitive/subfile.

[Willy Tschager]

I think that we can't simply correct geometry

I think that you're a spammer. Be careful.

w.

[SNIPE]

71708 has some strange sections that are always red no matter what colour I make the part:

I checked my settings in LDCAD and nothing changes it, and also reinstalled the official and unofficial LDRAW libraries.

Regards, Snipe

[Orion Pobursky]

As this is an unofficial part, I would suggest redownloading it.

[Philippe Hurbain]

As this is an unofficial part, I would suggest redownloading it.

Yes. I have a weird colored version too, but the one on PT is correct.

[Orion Pobursky]

Yes. I have a weird colored version too, but the one on PT is correct.

In comments, there was a hard coded surface that was corrected on 5/10. So if it was download before then, then you probably have an error.

[Gerald Lasser]

Since the part is so small, I can't be absolutely sure, but I don't think they are rounded. I think they are rectangular grooves with a flat outside. And using tori for features so small would be serious overkill. I think the walls of the divots are too sloped (should be closer to 90 degrees), resulting in the outer parts being too skinny.

I need to finally fix it, it has still some other issues

[SNIPE]

As this is an unofficial part, I would suggest redownloading it.

I downloaded the file on its own rather than the entire library, now it works, thx.

[Willy Tschager]

I noticed yesterday that the snowshoe, coming with the current Arctic Sets, is actually another type.

Now comes the dilemma. In our library there is the 30284, the original one and the 11187 which is currently listed as an alias.

At BL and Brickset however, the 11187 is NOT the same design as the 30284. Moreover there is another variant, the 28263, which is an alias to 11187.

The 11187 is official, but in reality it has another origin that 30284. Compared to 30284 it has a short front end and a long backend.

Ideal would be to change 11187 to the correct geometry and add an alias for 28263.

With that approach a complete compatibility cannot be guaranteed due to the different lenghts and existting models may face collision issues (though I think there is only a slim chance...)

To sum what we currently have:

30284 - Minifig Snowshoe  - The real thing - Official
11187 - =Minifig Snowshoe - Wrong alias as this is actually the short version - Official
11187a - Minifig Snowshoe with Short Toe Webbing - The real thing  - Unofficial
28263 - =Minifig Snowshoe with Short Toe Webbing - Alias to 11187a - Unofficial

I has been suggested to obsolate 11187 (which have never been done) and release 11187a and 28263 as official short versions. To get away from the 11187-mess I suggest:

* Obsolate 11187 as suggested
* Make 28263 the offiicial short version
* Make 11187a the alias of 28263

Thoughts?

w.

[Philippe Hurbain]

I'm fine with this scheme.