Parts Request: Ninjago Dragons Rising

[James Simpson]

Me again, sorry to be a pest. Here's my latest list:

https://www.bricklink.com/v2/catalog/cat...5#T=C&C=55 - Dragon, Baby with 4 Feet and Open Wings with Lime Eyes and Dark Blue Scales Pattern (Riyu)

https://www.bricklink.com/v2/catalog/cat...1#T=C&C=11 - Minifigure, Head, Modified Tiger with Braided Beard with Dark Pink Markings and Orange Eyes with Silver Outlines Pattern

https://www.bricklink.com/v2/catalog/cat...9#T=C&C=59 - Dragon Head (Ninjago) Jaw with 2 Bar Handles on Back with Lavender Eyes and Nougat Scales Pattern

https://www.bricklink.com/v2/catalog/cat...8#T=C&C=28 - Dragon Head (Ninjago) Jaw with Large Spike and 2 Bar Handles on Back

https://www.bricklink.com/v2/catalog/cat...=5#T=C&C=5 - Minifigure, Hair Female Bangs and Flipped Ends, Bun on Top with Pearl Gold Crescent Moon Pattern

Thank you in advance: also if theres the figure printings done already that would be a huge time saver

[Peter Grass]

Here are the raw parts. I made the horns pearl gold for 80831 since it was easy. I don't wanna do the other stuff though so you will have to decorate them yourself.

[James Simpson]

Here are the raw parts. I made the horns pearl gold for 80831 since it was easy. I don't wanna do the other stuff though so you will have to decorate them yourself.

That’s fine, you’ve already been a huge help!!!

[James Simpson]

I’m back again! Thanks in advance, I know there’s a lot here and some of them aren’t easy;

Large Figure Weapon, Blade Jagged with Axle Holder - https://www.bricklink.com/v2/catalog/cat...#T=C&C=115

Plastic Part for Set 71796 - Dragon Wing with Dark Blue Limb and Dark Azure and Bright Light Yellow Membranes Left Pattern- https://www.bricklink.com/v2/catalog/cat...a&#T=C&C=0

Dragon Head (Ninjago) Jaw Upper with Horns with Molded Dark Blue Face and Printed Bright Light Yellow Eyes, Dark Azure Electricity and Scales Pattern- https://www.bricklink.com/v2/catalog/cat...9#T=C&C=19

Dragon Head (Ninjago) Jaw with Spikes, 4 Studs and 2 Bar Handles with Molded Tan Face Pattern- https://www.bricklink.com/v2/catalog/cat...9#T=C&C=19

Plastic Part for Set 71797 - Junk Lug Sail with Bright Light Orange Dragon Wing Spines and Ninjago Logogram 'WIND' Left Pattern- https://www.bricklink.com/v2/catalog/cat...a&#T=C&C=0

Dragon Head (Ninjago) with Stepped Top and Pin Hole on Back with White Eyes, Bright Green and Yellowish Green Energy Markings Pattern- https://www.bricklink.com/v2/catalog/cat...0#T=C&C=80

Dragon Wing 19 x 11 with Bar Handle and 3 Pin Holes- https://www.bricklink.com/v2/catalog/cat...0#T=C&C=80

[Peter Grass]

76919 is on the tracker.

[James Simpson]

Back again, moving onto season 2 stuff now;

Minifigure, Weapon Sickle with Dragon Head and Long Wrapped Handle- https://www.bricklink.com/v2/catalog/cat...#T=C&C=115

Dragon Wing 11 x 5 with Bar Handles- https://www.bricklink.com/v2/catalog/cat...5#T=C&C=55

Minifigure, Hair Female with High Ponytail with Molded Dark Blue Headphones with Cat Ears Pattern- https://www.bricklink.com/v2/catalog/cat...#T=C&C=220

Minifigure, Weapon Sword with Molded Trans-Red Pommel, Jewel in Hilt, and Trailing Edge Pattern (Rageblade)- https://www.bricklink.com/v2/catalog/cat...7#T=C&C=77

Large Figure Weapon Sickle with Axle End and Axle Hole- https://www.bricklink.com/v2/catalog/cat...#T=C&C=115

Minifigure Armor Shoulder Pads and Bandana with Molded Pearl Gold Rivets and Scabbard for 2 Katanas Pattern- https://www.bricklink.com/v2/catalog/cat...lor=11#T=C

Minifigure, Hair Swept Back Tousled with Molded Bright Green Bandana Headband Pattern- https://www.bricklink.com/v2/catalog/cat...=2#T=C&C=2

Thank You in advance, I'm sure I'll be back at some point

[Peter Grass]

Here you go, the raw parts.

[James Simpson]

Here you go, the raw parts.

Thank you so much, but can I be cheeky? Do you possibly have the sword, armour and hair pieces with the molded colours? I can combine them myself like I have Lloyds hair

[Peter Grass]

You can do that yourself in ldparteditor. Open the file you want to change, hit F3, select one of the polygons on the model. Press select button and then select all with same colour, then click the paint palette icon on the right of the main window, show colour table, pick whatever colour you want and then hit the save icon.