Problems with 4526


Problems with 4526
#1
Hello!

I was wondering if someone could look into 4526. It's not quite right. There is some overlap, making it out of system.

[Image: 4526%20issue.jpg]
Reply
RE: Problems with 4526
#2
Hm, looks like you are right:
Code:
1 16 20 0 .34 1 0 0 0 1 0 0 0 1 s\67491s01.dat
1 16 20 0 .34 1 0 0 0 1 0 0 0 -1 s\67491s01.dat
1 16 20 0 .34 -1 0 0 0 1 0 0 0 1 connhole.dat
1 16 0 0 .34 -1 0 0 0 1 0 0 0 1 connhole.dat
1 16 -20 0 .34 -1 0 0 0 1 0 0 0 1 s\67491s01.dat
1 16 -20 0 .34 -1 0 0 0 1 0 0 0 -1 s\67491s01.dat
1 16 -20 0 .34 1 0 0 0 1 0 0 0 1 connhole.dat

1 16 20 0 -39.66 1 0 0 0 1 0 0 0 1 s\39790s01.dat
1 16 20 0 -79.66 1 0 0 0 1 0 0 0 -1 s\39790s01.dat
1 16 -20 0 -79.66 -1 0 0 0 1 0 0 0 -1 s\39790s01.dat
1 16 -20 0 -39.66 -1 0 0 0 1 0 0 0 1 s\39790s01.dat
nearly everything as minimal offset...
but you can fix it (should end in 0)
Reply
RE: Problems with 4526
#3
(2024-11-01, 9:48)Rene Rechthaler Wrote: Hm, looks like you are right:
Code:
1 16 20 0 .34 1 0 0 0 1 0 0 0 1 s\67491s01.dat
1 16 20 0 .34 1 0 0 0 1 0 0 0 -1 s\67491s01.dat
1 16 20 0 .34 -1 0 0 0 1 0 0 0 1 connhole.dat
1 16 0 0 .34 -1 0 0 0 1 0 0 0 1 connhole.dat
1 16 -20 0 .34 -1 0 0 0 1 0 0 0 1 s\67491s01.dat
1 16 -20 0 .34 -1 0 0 0 1 0 0 0 -1 s\67491s01.dat
1 16 -20 0 .34 1 0 0 0 1 0 0 0 1 connhole.dat

1 16 20 0 -39.66 1 0 0 0 1 0 0 0 1 s\39790s01.dat
1 16 20 0 -79.66 1 0 0 0 1 0 0 0 -1 s\39790s01.dat
1 16 -20 0 -79.66 -1 0 0 0 1 0 0 0 -1 s\39790s01.dat
1 16 -20 0 -39.66 -1 0 0 0 1 0 0 0 1 s\39790s01.dat
nearly everything as minimal offset...
but you can fix it (should end in 0)

Don't know how to fix that, unfortunately. My knowledge for this goes as far as importing it into Blender and that's it  Tongue
Reply
RE: Problems with 4526
#4
OK did it (just download the part, fix it and upload it back with "official file fix")
Reply
RE: Problems with 4526
#5
Fix is on the tracker:
https://library.ldraw.org/tracker/41601
Reply
« Next Oldest | Next Newest »



Forum Jump:


Users browsing this thread: 1 Guest(s)