How did universal Joint edit in LDCAD


How did universal Joint edit in LDCAD
#1
Sad 
How did universal Joint edit in LDCAD, Huh
Reply
RE: How did universal Joint edit in LDCAD
#2
(2018-12-28, 3:53)Shi.Yan Wrote: How did universal Joint edit in LDCAD, Huh
In order to flex a universal joint, you need to break it to its ends and centre components.
- Use these components directly (parts 62519 / 62520)
- or place the shortcut 61903 and "inline it" (break it into components): Select it -> right click -> reorganize -> inline.
Reply
RE: How did universal Joint edit in LDCAD
#3
(2018-12-28, 8:00)Philippe Hurbain Wrote:
(2018-12-28, 3:53)Shi.Yan Wrote: How did universal Joint edit in LDCAD, Huh
In order to flex a universal joint, you need to break it to its ends and centre components.
- Use these components directly (parts 62519 / 62520)
- or place the shortcut 61903 and "inline it" (break it into components): Select it -> right click -> reorganize -> inline.

thank you Very much,great help
Reply
RE: How did universal Joint edit in LDCAD
#4
Photo 
(2018-12-28, 9:17)Shi.Yan Wrote:
(2018-12-28, 8:00)Philippe Hurbain Wrote: In order to flex a universal joint, you need to break it to its ends and centre components.
- Use these components directly (parts 62519 / 62520)
- or place the shortcut 61903 and "inline it" (break it into components): Select it -> right click -> reorganize -> inline.

thank you Very much,great help


.png   Joint.png (Size: 47.98 KB / Downloads: 68)

How to change angle to connect two joints
Reply
RE: How did universal Joint edit in LDCAD
#5
Quote:How to change angle to connect two joints
The rotate pin, even in finest grid, can't go lower than 1°. So to get precise rotation you need to use the manual rotate tool where you are able to key in the rotation angle (toolbar round arrow, shortcut ctrl+r). Remember that you can put the angle value given by the measure tool sinply by clicking in the value box.

For more details, see the advanced editing tutorial, shock absorber section at bottom: http://www.melkert.net/LDCad/docs/advEdit
Reply
RE: How did universal Joint edit in LDCAD
#6
(2018-12-30, 9:02)Philippe Hurbain Wrote:
Quote:How to change angle to connect two joints
The rotate pin, even in finest grid, can't go lower than 1°. So to get precise rotation you need to use the manual rotate tool where you are able to key in the rotation angle (toolbar round arrow, shortcut ctrl+r). Remember that you can put the angle value given by the measure tool sinply by clicking in the value box.

For more details, see the advanced editing tutorial, shock absorber section at bottom: http://www.melkert.net/LDCad/docs/advEdit

I  had read it carefully,but i wish know more detail  about it .

Help document content is too small :-(
Reply
RE: How did universal Joint edit in LDCAD
#7
(2018-12-28, 8:00)Philippe Hurbain Wrote:
(2018-12-28, 3:53)Shi.Yan Wrote: How did universal Joint edit in LDCAD, Huh
In order to flex a universal joint, you need to break it to its ends and centre components.
- Use these components directly (parts 62519 / 62520)
- or place the shortcut 61903 and "inline it" (break it into components): Select it -> right click -> reorganize -> inline.

I had finished it. Thanks a lot.

next to do animate.


Attached Files
.png   Joint2.png (Size: 55.33 KB / Downloads: 33)
Reply
RE: How did universal Joint edit in LDCAD
#8
(2018-12-31, 5:45)Shi.Yan Wrote: next to do animate.
That's another story... good luck Wink
Reply
« Next Oldest | Next Newest »



Forum Jump:


Users browsing this thread: 1 Guest(s)