48245 and 92586


Re: 48245 and 92586
#20
Thanks! I only see gap from below where t01o1250 meets cone. There you can simply use a thin ring that slightly enter the cone to fill the gap (high diameter ring scaled down).

Otherwise you'll have to run Edger2 with expand subfile option to create additional condlines where top torus meets outer top cone. Maybe also add condlines where cone meets cylinder at bottom, but here it can be questionned as the slight break effet is rather nice (and condlines are not mandatory since it's a concave junction).
Reply
« Next Oldest | Next Newest »



Messages In This Thread
48245 and 92586 - by Max Martin Richter - 2012-11-07, 11:09
Re: 48245 and 92586 - by Stan Isachenko - 2012-11-07, 12:02
Re: 48245 and 92586 - by Max Martin Richter - 2012-11-07, 12:19
Re: 48245 and 92586 - by Philippe Hurbain - 2012-11-07, 13:38
Re: 48245 and 92586 - by Stan Isachenko - 2012-11-07, 13:50
Re: 48245 and 92586 - by Philippe Hurbain - 2012-11-07, 13:53
Re: 48245 and 92586 - by Philippe Hurbain - 2012-11-07, 16:38
Re: 48245 and 92586 - by Max Martin Richter - 2012-11-07, 19:07
Re: 48245 and 92586 - by Max Martin Richter - 2012-11-11, 22:27
Re: 48245 and 92586 - by Philippe Hurbain - 2012-11-12, 15:32
Re: 48245 and 92586 - by Max Martin Richter - 2012-11-12, 17:51
Re: 48245 and 92586 - by Michael Heidemann - 2012-11-12, 19:31
Re: 48245 and 92586 - by Philippe Hurbain - 2012-11-12, 19:42
Re: 48245 and 92586 - by Philippe Hurbain - 2012-11-12, 20:17
Re: 48245 and 92586 - by Max Martin Richter - 2012-11-12, 20:46
Re: 48245 and 92586 - by Philippe Hurbain - 2012-11-13, 6:08
Re: 48245 and 92586 - by Max Martin Richter - 2012-11-13, 16:23
Re: 48245 and 92586 - by Philippe Hurbain - 2012-11-13, 16:38
Re: 48245 and 92586 - by Max Martin Richter - 2012-11-13, 16:49
Re: 48245 and 92586 - by Philippe Hurbain - 2012-11-13, 18:42
Re: 48245 and 92586 - by Max Martin Richter - 2012-11-13, 19:00
Re: 48245 and 92586 - by Philippe Hurbain - 2012-11-13, 19:34
Re: 48245 and 92586 - by Max Martin Richter - 2012-11-13, 20:29
Re: 48245 and 92586 - by Philippe Hurbain - 2012-11-13, 20:35
Re: 48245 and 92586 - by Max Martin Richter - 2012-11-13, 20:42
Re: 48245 and 92586 - by Philippe Hurbain - 2012-11-14, 9:09
Re: 48245 and 92586 - by Max Martin Richter - 2012-11-14, 10:21

Forum Jump:


Users browsing this thread: 1 Guest(s)