LPub model & parts wont fit on page

[Jon]

Philippe,
The code was shown completely on the screenshot, nonetheless here it is:

0 Untitled
0 Name: Tutorial.ldr
0 Author: MLCad
0 Unofficial Model
0 ROTATION CENTER 0 0 0 1 "Custom"
0 ROTATION CONFIG 0 0
1 0 0 0 0 1 0 0 0 1 0 0 0 1 4600.dat
1 0 0 0 -40 1 0 0 0 1 0 0 0 1 4600.dat
0 STEP
1 7 0 -8 -50 1 0 0 0 1 0 0 0 1 3023.dat
1 7 10 -16 -20 0 0 -1 0 1 0 1 0 0 4531.dat
1 7 -10 -16 -20 0 0 -1 0 1 0 1 0 0 4531.dat
1 14 10 -16 -20 0 0 -1 0 1 0 1 0 0 4275b.dat
1 14 -10 -16 -20 0 0 -1 0 1 0 1 0 0 4275b.dat
0 STEP
1 14 -10 -16 -50 1 0 0 0 1 0 0 0 1 3024.dat
0 STEP
1 47 -10 -24 -50 1 0 0 0 1 0 0 0 1 3024.dat
1 47 -10 -32 -50 1 0 0 0 1 0 0 0 1 3024.dat
0 STEP
1 8 10 -16 -50 1 0 0 0 1 0 0 0 1 4073.dat
1 14 -10 -40 -50 1 0 0 0 1 0 0 0 1 3070b.dat
0 STEP
1 14 0 -40 0 0 0 -1 0 1 0 1 0 0 4871.dat
1 14 10 -40 -30 0 0 -1 0 1 0 1 0 0 3665.dat
1 14 -10 -40 -30 0 0 1 0 1 0 -1 0 0 3665.dat
0 STEP
1 14 0 -48 -40 1 0 0 0 1 0 0 0 1 3020.dat
0 ROTSTEP 0 0 180 ABS
1 7 0 8 -50 1 0 0 0 1 0 0 0 1 2540.dat
0 GROUP 2 Wheel Front Left
0 MLCAD BTG Wheel Front Left
1 7 30 5 -40 0 0 -1 0 1 0 1 0 0 4624.dat
0 MLCAD BTG Wheel Front Left
1 0 30 5 -40 0 0 -1 0 1 0 1 0 0 3641.dat
0 GROUP 2 Wheel Front Right
0 MLCAD BTG Wheel Front Right
1 7 -30 5 -40 0 0 1 0 -1 0 1 0 0 4624.dat
0 MLCAD BTG Wheel Front Right
1 0 -30 5 -40 0 0 1 0 -1 0 1 0 0 3641.dat
0 GROUP 2 Wheel Back Left
0 MLCAD BTG Wheel Back Left
1 7 30 5 0 0 0 -1 0 1 0 1 0 0 4624.dat
0 MLCAD BTG Wheel Back Left
1 0 30 5 0 0 0 -1 0 1 0 1 0 0 3641.dat
0 GROUP 2 Wheel Back Right
0 MLCAD BTG Wheel Back Right
1 7 -30 5 0 0 0 1 0 -1 0 1 0 0 4624.dat
0 MLCAD BTG Wheel Back Right
1 0 -30 5 0 0 0 1 0 -1 0 1 0 0 3641.dat
0 ROTSTEP END
0

I've tried a couple of simple .ldr files and get the same result each time.
Thanks again.