30116pb03, Panel 14x14x2.667 with Millennium Falcon Pattern

[Philippe Hurbain]

Very good job indeed!

Edger2 says the subfile is okay

Well... not quite, I see 4 red lines that at closer look are caused by needle shaped gaps.

And LDDP does report a few errors (see below).

Code:

Line 32: Quad collinear (angle = 179.972756397366): 4 16 279.75 56 -40.9 277.239 55.083 -43.509 275.819 55.086 -48.649 275.184 55.088 -50.951
Line 32: Quad points not coplaner (angle = 7.29169626473399): 4 16 279.75 56 -40.9 277.239 55.083 -43.509 275.819 55.086 -48.649 275.184 55.088 -50.951
Line 37: Quad points not coplaner (angle = 5.72276032249363): 4 16 220.519 24.409 -32.432 273.579 53.063 -42.512 279.75 56 -40.9 220.517 24.407 -32.428
Line 43: Quad points not coplaner (angle = 3.74873199767183): 4 0 220 24 -31.4286 219.7523 24.00001 -32.32164 220.449 24.37128 -32.419 220.5167 24.40729 -32.42815
Line 107: Quad points not coplaner (angle = 3.4744190042692): 4 16 204.751 24 -86.398 208.011 29.414 -100.995 210.525 30.771 -101.745 211.741 31.426 -102.101
Line 113: Quad points not coplaner (angle = 1.73648810918471): 4 16 230.611 47.914 -131.22 222.962 50.54 -154.126 223.561 50.822 -154.149 224.104 51.071 -154.148
Line 153: Quad collinear (angle = 179.950153191285): 4 320 185.594 27.471 -132.186 186.593 28.086 -132.767 186.164 27.296 -130.557 180.756 24.49 -129.366
Line 153: Quad points not coplaner (angle = 8.83407612376923): 4 320 185.594 27.471 -132.186 186.593 28.086 -132.767 186.164 27.296 -130.557 180.756 24.49 -129.366
Line 183: Quad points not coplaner (angle = 2.99758107262041): 4 16 212.124 44.983 -151.99 211.549 44.614 -151.598 204.994 43.32 -158.015 219.625 49.843 -157.25
Line 309: Quad collinear (angle = 179.938276819139): 4 16 205.928 23.34 -72.879 205.147 23.341 -75.71 204.995 24 -85.519 207.471 23.339 -67.309
Line 309: Quad points not coplaner (angle = 5.95382889817837): 4 16 205.928 23.34 -72.879 205.147 23.341 -75.71 204.995 24 -85.519 207.471 23.339 -67.309
Line 431: Triangle collinear (angle = 0.0215881040453166): 3 0 149.974 8.235 -62.301 192.22 20.41 -81.11 193.076 20.655 -81.471
Line 602: Quad points not coplaner (angle = 1.13742545117368): 4 16 34.736 28.948 -228.727 34.231 27.003 -225.076 32.42 24.404 -220.513 35.281 31.204 -232.975
Line 616: Quad points not coplaner (angle = 1.94343745738227): 4 16 98.143 52.16 -256.386 97.549 51.376 -255.022 45.531 31.202 -230.127 100.003 54.645 -260.714
Line 788: Quad points not coplaner (angle = 1.52608539348902): 4 0 50.341 14.921 -179.357 54.981 20.98 -201.691 55.189 21.212 -202.541 58.631 24 -212.454
Line 792: Quad points not coplaner (angle = 7.65794381496949): 4 16 55.189 21.212 -202.541 31.19 21.903 -211.889 31.316 22.147 -212.807 31.802 23.064 -216.246
Line 813: Quad collinear (angle = 179.951873944033): 4 16 23.864 8.254 -160.709 48.374 13.593 -174.727 47.547 12.673 -171.369 46.777 11.819 -168.254
Line 813: Quad points not coplaner (angle = 7.4258139162545): 4 16 23.864 8.254 -160.709 48.374 13.593 -174.727 47.547 12.673 -171.369 46.777 11.819 -168.254
Line 885: Quad points not coplaner (angle = 1.1101878957145): 4 0 113.882 14.297 -146.256 113.326 14.057 -145.535 129.422 21.296 -167.899 129.939 21.52 -168.571
Line 953: Quad collinear (angle = 179.914789113821): 4 16 61.974 8 -149.149 58.005 7.633 -148.344 52.601 7.634 -149.846 49.571 7.635 -150.693
Line 953: Quad points not coplaner (angle = 5.91787820710034): 4 16 61.974 8 -149.149 58.005 7.633 -148.344 52.601 7.634 -149.846 49.571 7.635 -150.693

Most can be split into appropriate triangles to solve the problem .
As for the header, I suggest the use of Datheader... that will not only correct headers issues (missing space in front of 2.667, ö of your name converted to UTF8) but also most of previous problems (only 2 very thin triangles remain).

How did you do projection on surface? Using Slicerpro? then maybe playing a bit with "precision" and/or unification thresholds would have eliminated some of the issues from the start?