new parts from set 75551

[SNIPE]

Hi,

set 75551 has some awesome new parts in it: https://www.bricklink.com/catalogItemInv.asp?S=75551-1

68568

68325

68327

bb1126


There is also new prints but im not as interested in those.

Regards, Snipe

[Magnus Forsberg]

I have already made three of them. Was only waiting for their numbers.


https://www.ldraw.org/cgi-bin/ptdetail.c.../68325.dat
https://www.ldraw.org/cgi-bin/ptdetail.c.../68568.dat
https://www.ldraw.org/cgi-bin/ptdetail.c.../67095.dat

Need more info on the bigger flat wheel.
Is it a 5x5 ? How deep is it? Offset?

[SNIPE]

I have already made three of them. Was only waiting for their numbers.


https://www.ldraw.org/cgi-bin/ptdetail.c.../68325.dat
https://www.ldraw.org/cgi-bin/ptdetail.c.../68568.dat
https://www.ldraw.org/cgi-bin/ptdetail.c.../67095.dat

Need more info on the bigger flat wheel.
Is it a 5x5 ?  How deep is it? Offset?

Thank you !!!

I think it is about 5.2L

[Vincent Messenet]

I have already made three of them. Was only waiting for their numbers.


https://www.ldraw.org/cgi-bin/ptdetail.c.../68325.dat
https://www.ldraw.org/cgi-bin/ptdetail.c.../68568.dat
https://www.ldraw.org/cgi-bin/ptdetail.c.../67095.dat

Need more info on the bigger flat wheel.
Is it a 5x5 ?  How deep is it? Offset?

I own the part so I can confirm you:
The size is 5x5
The depth is 20 LDU
The offset is 8 LDU

[Magnus Forsberg]

75551 - Brick-built Minions and their Lair

   

   

After making the parts, I had to build the models, right?

Thanks to Vincent for making the printed parts.
Thanks to Orion for making the minifig weapon Sai, 98139.
Only part missing is the correct sword, 25111.
And all the stickers.

[Vincent Messenet]

Nice! Thanks for sharing

[Vincent Messenet]

If someone wants to author the stickers here is a scan

[Gerald Lasser]

Vincent, so you have the bb1126 (68211) part as well?

It is difficult to get the dimensions/angles right with the present picture.

Can you please make a set of pictures that show the angle of each of the three prongs?

Thansk!

[Vincent Messenet]

Vincent, so you have the bb1126 (68211) part as well?

It is difficult to get the dimensions/angles right with the present picture.

Can you please make a set of pictures that show the angle of each of the three prongs?

Thansk!

Yes, sure I can!

I did some photos with my phone:
https://drive.google.com/file/d/17dXpuv2...haring,%20
https://drive.google.com/file/d/1af_hnse...haring,%20
https://drive.google.com/file/d/1jCdwJ6T...haring,%20

Let me know if you need any other angle

[Rolf Osterthun]

If someone wants to author the stickers here is a scan

Hey,

here is the sticker no. 2. It is the first sticker I made. I hope it is usable.

Rolf

[Magnus Forsberg]

here is the sticker no. 2. It is the first sticker I made. I hope it is usable.

It would be if you take it a little bit longer. Attached is a clean-up I made.

Reduced number of decimals. 2 is enough, except where the pattern attaches to the subfile. Then 4.
Sorted the colours.
Added a 4-4ering primitive, to close the pattern in hi-res mode of the subfile. Add correct colour on the ering.