LDraw.org Discussion Forums
2x2 curved round brick corner from set 77002 - Printable Version

+- LDraw.org Discussion Forums (https://forums.ldraw.org)
+-- Forum: Models and Parts (https://forums.ldraw.org/forum-18.html)
+--- Forum: Part Requests (https://forums.ldraw.org/forum-30.html)
+--- Thread: 2x2 curved round brick corner from set 77002 (/thread-28484.html)

2x2 curved round brick corner from set 77002 - SNIPE - 2024-11-02

Hi,

Can I get the new 2x2 round curved corner brick by any chance

It's from set 77002 - Metal Sonic v Cyclone

The height is 1 brick tall (but no studs) and the inner diameter if you put 4 together is 2L

There are 4 in yellow, on the front of the robot which makes a 4x4 ring.


.png   sonic.png (Size: 257.96 KB / Downloads: 298)

RE: 2x2 curved round brick corner from set 77002 - Rene Rechthaler - 2024-11-02

Sounds like a Mixed-Mode Torus Outside  1 x 1.0000 x 0.25 (48\rm04o1000.dat)
0 // Major Radius: 1
0 // Tube(Minor) Radius: 1

and a regular resolution inside tube to fit 11833.dat

do we have a partnumber? and a view of the underside?

Edit: upper part could look like that:
1 16 0 -4 0 20 0 0 0 -20 0 0 0 -20 48\rm04o1000.dat
1 16 0 -24 0 20 0 0 0 1 0 0 0 -20 48\1-4aring.dat
1 16 0 -24 0 20 0 0 0 1 0 0 0 -20 1-4edge.dat
0 BFC INVERTNEXT
1 16 0 -4 0 20 0 0 0 -20 0 0 0 -20 1-4cyli.dat
1 16 20 -4 0 20 0 0 0 0 -20 0 -1 0 1-4disc.dat
1 16 20 -4 0 20 0 0 0 0 -20 0 -1 0 1-4edge.dat
1 16 0 -4 -20 0 1 0 -20 0 0 0 0 -20 1-4disc.dat
1 16 0 -4 -20 0 1 0 -20 0 0 0 0 -20 1-4edge.dat
2 24 0 -4 -20 0 -24 -20
2 24 20 -4 0 20 -24 0

RE: 2x2 curved round brick corner from set 77002 - Jeff Jones - 2024-11-02

hello made very crude version of it

RE: 2x2 curved round brick corner from set 77002 - SNIPE - 2024-11-03

thx Big Grin

RE: 2x2 curved round brick corner from set 77002 - Rene Rechthaler - 2024-11-03

(2024-11-02, 22:15)Jeff Jones Wrote: hello made very crude version of it

that part is too high (28LDU instead of normal brick height of 24)

RE: 2x2 curved round brick corner from set 77002 - Jeff Jones - 2024-11-04

(2024-11-03, 15:03)Rene Rechthaler Wrote: that part is too high (28LDU instead of normal brick height of 24)
me could rework tomorrow

RE: 2x2 curved round brick corner from set 77002 - Jeff Jones - 2024-11-28

underside of the brick revealed
from ashenflash's review
looks like a macaroni piece

RE: 2x2 curved round brick corner from set 77002 - Magnus Forsberg - 2024-11-28

(2024-11-28, 22:18)Jeff Jones Wrote: ...
looks like a macaroni piece

Same design as 85080.dat then.

RE: 2x2 curved round brick corner from set 77002 - Rene Rechthaler - 2024-11-28

same origin too?
should i split the 48\rm04o1000.dat?
what about the curved inside? i would guess no prim there...
rest of the part also gets split?

RE: 2x2 curved round brick corner from set 77002 - Jeff Jones - 2024-11-28

changed

RE: 2x2 curved round brick corner from set 77002 - Gerald Lasser - 2024-11-29

We also get a nice 2x2 round quarter dome piece

RE: 2x2 curved round brick corner from set 77002 - SNIPE - 2024-12-05

(2024-11-28, 23:20)Jeff Jones Wrote: changed
Thx
(2024-11-29, 20:07)Gerald Lasser Wrote: We also get a nice 2x2 round quarter dome piece
Is this a new piece, or the piece I mentioned in this thread?

RE: 2x2 curved round brick corner from set 77002 - Gerald Lasser - 2024-12-05

(2024-12-05, 6:54)SNIPE Wrote: Thx
Is this a new piece, or the piece I mentioned in this thread?

New, looks like the flat 3x3

RE: 2x2 curved round brick corner from set 77002 - SNIPE - 2024-12-06

(2024-12-05, 13:52)Gerald Lasser Wrote: New, looks like the flat 3x3

show me it, it isnt just either of these right?

[Image: lego-88293-round-brick-3x3x2-quarter-dom...-green.jpg][Image: 6441096.jpg]

RE: 2x2 curved round brick corner from set 77002 - Gerald Lasser - 2024-12-06

(2024-12-06, 10:48)SNIPE Wrote: show me it, it isnt just either of these right?

[Image: lego-88293-round-brick-3x3x2-quarter-dom...-green.jpg][Image: 6441096.jpg]

like the right one, heres a pic:
   

RE: 2x2 curved round brick corner from set 77002 - SNIPE - 2024-12-07

(2024-12-06, 16:23)Gerald Lasser Wrote: like the right one, heres a pic:

ooh ok, but in 2x2 form, yes this  is useful

RE: 2x2 curved round brick corner from set 77002 - SNIPE - 2025-03-02

I see 5852 on the parts tracker now, cool.

Any progress on part 5924? I don't see it on the parts tracker or in my ldraw libs

Regards

RE: 2x2 curved round brick corner from set 77002 - Rene Rechthaler - 2025-03-03

(2025-03-02, 21:03)SNIPE Wrote: I see 5852 on the parts tracker now, cool.

Any progress on part 5924? I don't see it on the parts tracker or in my ldraw libs

Regards


.dat   5924.dat (Size: 15.71 KB / Downloads: 7)
something like this?
(nearly finished, needs a name)
should it get cut in half? (big part)

RE: 2x2 curved round brick corner from set 77002 - SNIPE - 2025-03-03

(2025-03-03, 11:29)Rene Rechthaler Wrote: something like this?
(nearly finished, needs a name)
should it get cut in half? (big part)

Yeah this looks fine, the top face just needs merging with the rest of the part:

[Image: 4-FFB0-D2-A-F321-40-A3-B978-CF5-A397-FA74-E.png]

RE: 2x2 curved round brick corner from set 77002 - Rene Rechthaler - 2025-03-03

Done, uploaded to the PT
https://library.ldraw.org/parts/44476

RE: 2x2 curved round brick corner from set 77002 - SNIPE - 2025-03-03

(2025-03-03, 18:35)Rene Rechthaler Wrote: Done, uploaded to the PT
https://library.ldraw.org/parts/44476

Many thanks.