LDraw.org Discussion Forums

This part:

https://www.bricklink.com/v2/catalog/cat...3#T=C&C=11

Is super useful used either as a 5th wheel or just a technic connector block.

It would be cool if it is in LDRAW but idk if anyone has it yet but,

I may buy some to use IRL so can maybe help figure out some of the geometry

I can see that it has 2x2 then 2x2 holes on the front, the inner of which are thru holes that span 3L. The two gaps cannot hold say a 1x1 beam because on the underside there is a face like on technic panels.





Regards, Snipe

Pictures and videos are a bit scarce...

I got this input, where the part is shown a bit at the 1:57 mark: https://www.youtube.com/watch?v=wxBYtpn26vM

I have added the results so far, Inside is difficult the judge
[attachment=5651]

(2020-08-19, 23:15)Gerald Lasser Wrote: [ -> ]Pictures and videos are a bit scarce...

I got this input, where the part is shown a bit at the 1:57 mark: https://www.youtube.com/watch?v=wxBYtpn26vM

I have added the results so far, Inside is difficult the judge

Thanks, can you post a dat file with the subfiles/primatives connected as I don't know how to mirror subfiles/primatives. right clicking then hitting mirror isnt doing anything.

Regards, Snipe

(2020-08-20, 1:37)SNIPE Wrote: [ -> ]Thanks, can you post a dat file with the subfiles/primatives connected as I don't know how to mirror subfiles/primatives. right clicking then hitting mirror isnt doing anything.

Regards, Snipe

Try copying the files into your "unofficial parts" (67139) and "unofficial parts/s" (67139s01) folders, that should work.

I found another picture that reveals some details on the gap.

(2020-08-20, 9:48)Gerald Lasser Wrote: [ -> ]Try copying the files into your "unofficial parts" (67139) and "unofficial parts/s" (67139s01) folders, that should work.

I found another picture that reveals some details on the gap.

Ah got it now it works, the 67139s01 had to be in s not ldrawunf

Thanks.

(2020-08-20, 9:48)Gerald Lasser Wrote: [ -> ]I found another picture that reveals some details on the gap.

Looks like direct link to the image is not allowed by the website

(2020-08-20, 18:25)Philippe Hurbain Wrote: [ -> ]Looks like direct link to the image is not allowed by the website

You can refresh the page, or copy/paste the url (into a new tab) and the image will show up because then it's no redirected/referred request anymore.

(2020-08-19, 23:15)Gerald Lasser Wrote: [ -> ]Pictures and videos are a bit scarce...

I got this input, where the part is shown a bit at the 1:57 mark: https://www.youtube.com/watch?v=wxBYtpn26vM

I have added the results so far, Inside is difficult the judge

Any chance of this making it to the PT any time soon?

(2020-11-20, 19:32)Orion Pobursky Wrote: [ -> ]Any chance of this making it to the PT any time soon?

I will upload it with "needs Work"

I will get one next week, then I can verify the cutout

(2020-11-20, 19:49)Gerald Lasser Wrote: [ -> ]I will upload it with "needs Work"

I will get one next week, then I can verify the cutout

I ordered a bunch of these on bricklink a while back, so I can post details photos if needed.

Got my part! It's finished and uploaded

https://www.ldraw.org/cgi-bin/ptdetail.c.../67139.dat

(2020-11-26, 22:17)Gerald Lasser Wrote: [ -> ]Got my part! It's finished and uploaded

https://www.ldraw.org/cgi-bin/ptdetail.c.../67139.dat

Awesome. Thanks. Can put it in the Batwing now instead of the placeholder I have at the moment.