2016-01-15, 1:35
2016-01-15, 1:35
2022-08-13, 14:07
I'd also like to make request for these sails for creating OMR sets 6057, 6261 and 6277.
The part number is u767 and they are three existing print variants.
sailbb19 -> u767p40
sailbb26 -> u767p30
sailbb30 -> u767p31
http://peeron.com/inv/parts/x767px1
Plain part (flat and formed) is sufficient, as I will try to do patterning them by myself.
The part number is u767 and they are three existing print variants.
sailbb19 -> u767p40
sailbb26 -> u767p30
sailbb30 -> u767p31
http://peeron.com/inv/parts/x767px1
Plain part (flat and formed) is sufficient, as I will try to do patterning them by myself.
2022-10-12, 8:18
(2022-08-13, 14:07)Takeshi Takahashi Wrote: [ -> ]I'd also like to make request for these sails for creating OMR sets 6057, 6261 and 6277.Blank flat version is done, https://www.ldraw.org/cgi-bin/ptdetail.c...s/u767.dat
The part number is u767 and they are three existing print variants.
sailbb19 -> u767p40
sailbb26 -> u767p30
sailbb30 -> u767p31
http://peeron.com/inv/parts/x767px1
Plain part (flat and formed) is sufficient, as I will try to do patterning them by myself.
Also attached an undistorted image of px1 for patterning
2022-10-17, 9:46
2022-10-17, 13:01
(2022-10-17, 9:46)Philippe Hurbain Wrote: [ -> ]First formed shape now on PT:
https://www.ldraw.org/cgi-bin/ptdetail.c...767c01.dat
Thanks very much!!
Fit check is here: https://forums.ldraw.org/thread-26632-po...l#pid47349
I think the sail surface is clearing the stud of 4733, so the stud edge should be a rendering error.
I'll make the print after the requested part 3068bpb2007 completed.
2022-10-19, 14:49
First flat print is done!!
https://www.ldraw.org/cgi-bin/ptdetail.c...767p01.dat
Now started this formed part
https://www.ldraw.org/cgi-bin/ptdetail.c...767p01.dat
Now started this formed part
2022-10-19, 19:53
(2022-10-19, 14:49)Takeshi Takahashi Wrote: [ -> ]Now started this formed part
Good luck 😁
2022-10-26, 15:09
2022-10-30, 15:33
2022-10-31, 12:35
(2022-10-30, 15:33)Philippe Hurbain Wrote: [ -> ]Third and last shape on PT!
https://www.ldraw.org/cgi-bin/ptdetail.c...767c03.dat
Thanks very much!! I'll check them.
2022-12-11, 14:11
Finally the first printed sail has been done!!
https://www.ldraw.org/cgi-bin/ptdetail.c...p01c01.dat
[attachment=8792]
https://www.ldraw.org/cgi-bin/ptdetail.c...p01c01.dat
[attachment=8792]
2022-12-11, 17:04
That part is amazing! Well done.
2022-12-12, 11:40
2022-12-24, 13:28
(2022-12-12, 11:40)Takeshi Takahashi Wrote: [ -> ]Fit check for set 6261 is OK!!
Thanks, I'll start creating print.
The second print is done!!
https://www.ldraw.org/cgi-bin/ptdetail.c...p02c02.dat
[attachment=8860]