BEAD004 From Lego Pens


RE: BEAD004 From Lego Pens
#2
I don't know why you used the box4t and this quad  for the outside

1 16 0 30 0 15 0 0 0 -30 0 0 0 15 box4t.dat
4 16 -15 30 -15 -15 0 -15 15 0 -15 15 30 -15

Shorten the stud4:
1 16 0 4 0 1 0 0 0 -6.5 0 0 0 1 stud4a.dat


You can't use a box5 for the inside, so instead of:
0 BFC INVERTNEXT
1 16 0 30 0 12 0 0 0 -26 0 0 0 12 box5.dat

use:
0 BFC INVERTNEXT
1 16 0 30 0 12 0 0 0 -26 0 0 0 12 box4.dat
1 16 0 4 0 8 0 0 0 -1 0 0 0 8 4-4ndis.dat
4 16 -12 4 -12 -12 4 12 -8 4 8 -8 4 -8
4 16 -12 4 -12 -8 4 -8 8 4 -8 12 4 -12
4 16 12 4 -12 8 4 -8 8 4 8 12 4 12
4 16 -12 4 12 12 4 12 8 4 8 -8 4 8



The outer box instead of:
1 16 0 30 0 15 0 0 0 -30 0 0 0 15 box4t.dat

construct it like this:
1 16 0 30 0 15 0 0 0 -30 0 0 0 15 box4.dat
1 16 0 0 0 6 0 0 0 1 0 0 0 6 4-4ndis.dat
4 16 -6 0 6 6 0 6 15 0 15 -15 0 15
4 16 -6 0 6 -15 0 15 -15 0 -15 -6 0 -6
4 16 -6 0 -6 -15 0 -15 15 0 -15 6 0 -6
4 16 6 0 -6 15 0 -15 15 0 15 6 0 6


Now the top stud2 needs to get rid of the inner edge lines, replace:
1 16 0 0 0 1 0 0 0 1 0 0 0 1 stud2.dat

with:
1 16 0 0 0 1 0 0 0 1 0 0 0 1 stud2.dat
1 16 0 0 0 6 0 0 0 1 0 0 0 6 4-4edge.dat


and extend the hole to the stud4 with:
0 BFC INVERTNEXT
1 16 0 0 0 4 0 0 0 4 0 0 0 4 4-4cyli.dat
1 16 0 4 0 4 0 0 0 1 0 0 0 4 4-4edge.dat
1 16 0 4 0 2 0 0 0 -1 0 0 0 2 4-4ring2.dat


Hope that helps
Reply
« Next Oldest | Next Newest »



Messages In This Thread
BEAD004 From Lego Pens - by SNIPE - 2020-09-02, 8:56
RE: BEAD004 From Lego Pens - by Gerald Lasser - 2020-09-02, 22:47
RE: BEAD004 From Lego Pens - by SNIPE - 2020-09-03, 4:13
RE: BEAD004 From Lego Pens - by Gerald Lasser - 2020-09-03, 10:45
RE: BEAD004 From Lego Pens - by SNIPE - 2020-09-03, 13:17

Forum Jump:


Users browsing this thread: 1 Guest(s)