[LDPartEditor] 0.8.7 Beta Released


Re: [LDPartEditor] Select connected selects too much
#8
In the code below, if I select the quad then select -> select connected, the elements of the cylo (not the cylo itself) gets selected. If I then try to move the selection, only the quad moves.
Code:
1 16 -10 1 28 -2 0 0 0 2 0 0 0 -2 1-4cylo.dat
4 16 -12 1 60 -12 1 28 -12 3 28 -12 3 60
Worse, if I cut the selection then copy, I get the following result:
Code:
1 16 -10 1 28 -2 0 0 0 2 0 0 0 -2 1-4cylo.dat
2 24 -11.8478 1 27.2346 -11.4142 1 26.5858
2 24 -11.8478 3 27.2346 -11.4142 3 26.5858
2 24 -12 1 28 -11.8478 1 27.2346
2 24 -12 3 28 -11.8478 3 27.2346
2 24 -10.7654 1 26.1522 -10 1 26
2 24 -10.7654 3 26.1522 -10 3 26
2 24 -11.4142 1 26.5858 -10.7654 1 26.1522
2 24 -11.4142 3 26.5858 -10.7654 3 26.1522
4 16 -12 3 28 -11.8478 3 27.2346 -11.8478 1 27.2346 -12 1 28
4 16 -11.8478 3 27.2346 -11.4142 3 26.5858 -11.4142 1 26.5858 -11.8478 1 27.2346
4 16 -11.4142 3 26.5858 -10.7654 3 26.1522 -10.7654 1 26.1522 -11.4142 1 26.5858
4 16 -10.7654 3 26.1522 -10 3 26 -10 1 26 -10.7654 1 26.1522
5 24 -12 1 28 -12 3 28 -11.8478 1 27.2346 -12 1 30
5 24 -11.8478 1 27.2346 -11.8478 3 27.2346 -11.4142 1 26.5858 -12 1 28
5 24 -11.4142 1 26.5858 -11.4142 3 26.5858 -10.7654 1 26.1522 -11.8478 1 27.2346
5 24 -10.7654 1 26.1522 -10.7654 3 26.1522 -10 1 26 -11.4142 1 26.5858
5 24 -10 1 26 -10 3 26 -10.7654 1 26.1522 -8 1 26
4 16 -12 1 60 -12 1 28 -12 3 28 -12 3 60
Reply
« Next Oldest | Next Newest »



Messages In This Thread
Re: [LDPartEditor] Select connected selects too much - by Philippe Hurbain - 2016-03-24, 15:35
Intersector - by Nils Schmidt - 2016-03-24, 16:26
Re: Intersector - by Willy Tschager - 2016-03-25, 12:54
Re: Intersector - by Magnus Forsberg - 2016-03-25, 13:40

Forum Jump:


Users browsing this thread: 2 Guest(s)