LDraw.org Discussion Forums
LDView Bug - Printable Version

+- LDraw.org Discussion Forums (https://forums.ldraw.org)
+-- Forum: LDraw Programs (https://forums.ldraw.org/forum-7.html)
+--- Forum: LDraw Editors and Viewers (https://forums.ldraw.org/forum-11.html)
+--- Thread: LDView Bug (/thread-3070.html)

Pages: 1 2


LDView Bug - Christoph Mierowski - 2012-01-15

I recognized, that if I use the primitive substitution option with models that have xxxxh.DAT baseplates in them the whole program does crash.
With xxxxh.DAT I mean the baseplate with detailed underside studs - only for the case these get renamed.....

Is this error known ?
Will it be fixed?


Re: LDView Bug - Jean-Philippe Ouellet - 2012-01-15

I am unable to reproduce the issue as of version 4.1 (latest that I am aware of) on mac.

The part:
[Image: zpVsX.png]

A model using the part:
[Image: cm4xz.png]

It did take a little while to load the first time because it tried to find an update for the part and a few subparts (some are still unofficial) and during that time the interface did become unresponsive for a few seconds, but it loaded just fine. Please elaborate on "crash" and please tell us what version/system you are running on, and what part, specifically, you have issues with.


Re: LDView Bug - Travis Cobbs - 2012-01-16

Where can I find the h versions of the baseplates?


Re: LDView Bug - Travis Cobbs - 2012-01-17

It doesn't crash on my Mac either, but it does use a fair bit of memory. Loading just the 50x50 baseplate with underside in LDView causes LDView to use about 228MB, while loading the standard one causes LDView to use about 66MB. I'll have to test on my Windows machine to see if it crashes there, but I don't see any particular reason why it should.

Also, check the "Curve quality" slider setting on the Primitives page of LDView's preferences. The default for that slider is the second notch, and anything above that will have a huge impact on memory usage of the baseplate with underside, with a much lower impact on the memory usage of the standard baseplate. For example, bumping the slider from the second notch to the third caused memory usage for the standard one to go from 66MB to 74MB, while the one with underside went from 228MB to 409MB.

For reference, the h version uses 643MB on the fourth notch, and that's just the one part. Also, no matter how much memory you have, LDView is a 32-bit app, so it will crash if it ever needs more than 2GB (or perhaps 3GB, but I don't think so).


Re: LDView Bug - Travis Cobbs - 2012-01-17

The 50x50 baseplate with underside loaded without any problem for me in Windows also (and used quite a bit less memory than on my Mac; memory usage in LDView is very dependend on video card drivers, though). Based on your original post, it seems you're having the problem with all the XXXXh.dat baseplates, but if the 50x50 (which I chose because it is the largest) loads for you, please give me a specific example of one that causes a crash.


Re: LDView Bug - Tim Gould - 2012-01-17

Chris Dee Wrote:Only on the Parts Tracker - e.g. her. I'm not yet convinced this is a good idea, or sure how we should implement it in the Parts Library.

I split off Chris' reply due to veer in the conversation

http://forums.ldraw.org/showthread.php?tid=3095

Tim


Re: LDView Bug - Christoph Mierowski - 2012-01-18

The problems begin with the 16 x 16 baseplates- first it needs a huge amount of time to get the parsing done then I get this error messages:
[Image: gEuLG]

All xxxxh.DAT baseplates which are bigger are even worse and they all crash with that error message.

Currently I run LDView on Windows XP 64 Profesional SP2

I have a 2,3 GHz Intel Dualcore, ATI RAdion HD graphic card with 512 MB RAM, and 4 GB DDR2 RAM-

hope you can tell me what goes wrong....


Re: LDView Bug - Travis Cobbs - 2012-01-19

I'm not 100% sure, but the error you're seeing appears to be due to LDView running out of memory. I have no idea why this would happen to you with a 16x32 baseplate, unless you have the curve quality set (way) above the second notch. Make sure that's set to the second notch, and if it is, try setting the Memory usage setting to Medium or Low in the General tab of LDView's preferences.


Re: LDView Bug - Christoph Mierowski - 2012-01-19

yes that was the error - I tried a model with 2 16x16 and one 16x32 baseplate and it does crash when I set the curve quality above the 6 notch (seen from left)....


Re: LDView Bug - Steffen - 2012-01-19

can you please post the file here, so it is available for playing around?