LDraw.org Discussion Forums
[Complete] Technic Ring ⌀=11L, inner ⌀=9L - Printable Version

+- LDraw.org Discussion Forums (https://forums.ldraw.org)
+-- Forum: Models and Parts (https://forums.ldraw.org/forum-18.html)
+--- Forum: Part Requests (https://forums.ldraw.org/forum-30.html)
+--- Thread: [Complete] Technic Ring ⌀=11L, inner ⌀=9L (/thread-24639.html)



Technic Ring ⌀=11L, inner ⌀=9L - SNIPE - 2021-05-21

Hi,

I'm not sure if its too early to get this part as it does not have an official part number/ID yet

It's outer diameter looks to be 11L, its inner diameter looks to be 9L and its thickness is 1L.

It is the new technic ring that comes in set 41686, it looks fairlyy easy to make luckily, here is a picture

[Image: 1.png]
And here is a 360 degree view: https://youtu.be/EsVsxQWKfkk


RE: Technic Ring ⌀=11L, inner ⌀=9L - Gerald Lasser - 2021-05-21

(2021-05-21, 11:44)SNIPE Wrote: Hi,

I'm not sure if its too early to get this part as it does not have an official part number/ID yet

It's outer diameter looks to be 11L, its inner diameter looks to be 9L and its thickness is 1L.

It is the new technic ring that comes in set 41686, it looks fairlyy easy to make luckily, here is a picture

[Image: 1.png]
And here is a 360 degree view: https://youtu.be/EsVsxQWKfkk

Yes, that is an interesting part, i do habe two Friends Sets for review, but unfortunately not this one. I did a draft already, can upload here. 
Radius to the centre of the connhole is 5 studs


RE: Technic Ring ⌀=11L, inner ⌀=9L - SNIPE - 2021-05-21

(2021-05-21, 12:26)Gerald Lasser Wrote: Yes, that is an interesting part, i do habe two Friends Sets for review, but unfortunately not this one. I did a draft already, can upload here. 

Yes please!.

Thanks, Snipe.


RE: Technic Ring ⌀=11L, inner ⌀=9L - Gerald Lasser - 2021-05-21

Here's the draft! Note that there is a liftarm in as a helper.

I can't finish it within the next four days. So if anybody, go ahead.


RE: Technic Ring ⌀=11L, inner ⌀=9L - Philippe Hurbain - 2021-05-22

(2021-05-21, 21:10)Gerald Lasser Wrote: Here's the draft! Note that there is a liftarm in as a helper.

I can't finish it within the next four days. So if anybody, go ahead.
I'll do!


RE: Technic Ring ⌀=11L, inner ⌀=9L - Philippe Hurbain - 2021-05-22

(2021-05-22, 9:13)Philippe Hurbain Wrote: I'll do!
Here is the completed part. Don't forget to get new primitives, now on PT.


RE: Technic Ring ⌀=11L, inner ⌀=9L - SNIPE - 2021-05-23

(2021-05-22, 16:05)Philippe Hurbain Wrote: Here is the completed part. Don't forget to get new primitives, now on PT.

Thanks.


RE: Technic Ring ⌀=11L, inner ⌀=9L - Mark Kennedy - 2021-06-01

brickset list the part number as 77107

https://brickset.com/parts/design-77107


RE: Technic Ring ⌀=11L, inner ⌀=9L - Philippe Hurbain - 2021-06-01

(2021-06-01, 14:09)Mark Kennedy Wrote: brickset list the part number as 77107

https://brickset.com/parts/design-77107
Thanks. Now on PT...
https://www.ldraw.org/cgi-bin/ptdetail.cgi?f=parts/77107.dat