[Complete] Minifig Hat Bicorner with Black Admiral Pattern - 2528px2 - Printable Version +- LDraw.org Discussion Forums (https://forums.ldraw.org) +-- Forum: Models and Parts (https://forums.ldraw.org/forum-18.html) +--- Forum: Part Requests (https://forums.ldraw.org/forum-30.html) +--- Thread: [Complete] Minifig Hat Bicorner with Black Admiral Pattern - 2528px2 (/thread-24563.html) |
Minifig Hat Bicorner with Black Admiral Pattern - 2528px2 - Tomasz - 2021-04-17 Hi I'm looking for Minifig Hat Bicorner with Black Admiral Pattern - 2528px2. Tomasz RE: Minifig Hat Bicorner with Black Admiral Pattern - 2528px2 - Gerald Lasser - 2021-04-17 here you are https://www.ldraw.org/cgi-bin/ptdetail.cgi?f=parts/2528p32.dat don't forget the subfile RE: Minifig Hat Bicorner with Black Admiral Pattern - 2528px2 - Gerald Lasser - 2021-04-19 Taking the discussion form the part s\2528s01 to the forum Magnus, here's my proposal for the rework. - based on the Unity/LDD geometry - measurements confirmed with calipers - I broke down the LDD geometry and refined it a bit, hopefully not adding too many surfaces. What changed? - Plume attachment point - Top width increased - Bottom width decreased - Rounded ends What is pending? - Runded gap in the middle Please check the outer surfcase! Thanks Gerald RE: Minifig Hat Bicorner with Black Admiral Pattern - 2528px2 - Magnus Forsberg - 2021-04-19 I think it looks good. But I prefer the simpler ldd outer surface mesh. The edge on yours is better, though. It needs a full 180 rotation, the plume is allways on the left side. And the rounded ends should be more flat. 4 9 -26.25 7.5 -3.33 -26.012 4.623 -2.95 -26.012 4.623 2.95 -26.25 7.5 3.33 2 11 -26.012 4.623 2.95 -26.25 7.5 3.33 2 11 -26.012 4.623 -2.95 -26.25 7.5 -3.33 RE: Minifig Hat Bicorner with Black Admiral Pattern - 2528px2 - Gerald Lasser - 2021-04-20 Here's a proposal in the middle LDD some 30+ surfaces Surface: 65 surfaces Redone: Surface-2 44 surfaces RE: Minifig Hat Bicorner with Black Admiral Pattern - 2528px2 - Philippe Hurbain - 2021-04-20 (2021-04-20, 12:45)Gerald Lasser Wrote: Here's a proposal in the middleLooks to be a good compromise! RE: Minifig Hat Bicorner with Black Admiral Pattern - 2528px2 - Magnus Forsberg - 2021-04-20 (2021-04-20, 14:20)Philippe Hurbain Wrote: Looks to be a good compromise! I like it too. RE: Minifig Hat Bicorner with Black Admiral Pattern - 2528px2 - Magnus Forsberg - 2021-04-24 A new version of the hats, and a new print, is now done. https://www.ldraw.org/cgi-bin/ptscan.cgi?q=bicorne RE: Minifig Hat Bicorner with Black Admiral Pattern - 2528px2 - Gerald Lasser - 2021-04-26 Small request, big results! A request for the Admiral's Hat resulted in the correction of the geometry and making all patterns available! Magnus is working on the last one, soe here's the Family Picture of today with one member on the way: RE: Minifig Hat Bicorner with Black Admiral Pattern - 2528px2 - Tomasz - 2021-04-26 Thanks RE: Minifig Hat Bicorner with Black Admiral Pattern - 2528px2 - Magnus Forsberg - 2021-04-26 And now the last version is on the Part Tracker. https://www.ldraw.org/cgi-bin/ptscan.cgi?q=2528a&scope=header https://www.ldraw.org/cgi-bin/ptpatterns.cgi?p=2528a Here's a summary of all the files |