LDraw.org Discussion Forums
Parts we are Working on - Part Deux - Printable Version

+- LDraw.org Discussion Forums (https://forums.ldraw.org)
+-- Forum: Models and Parts (https://forums.ldraw.org/forum-18.html)
+--- Forum: Part Requests (https://forums.ldraw.org/forum-30.html)
+--- Thread: Parts we are Working on - Part Deux (/thread-23790.html)

Pages: 1 2 3 4 5 6 7 8 9 10 11


Parts we are Working on - Part Deux - Gerald Lasser - 2019-12-17

...as the original thread spans now over seven years, I dare to open a new one. The old one is also taking quite some time to load...

So here I go:

New Train Parts:

- 38340 Wheel with Pin -> 26.12.: on the PT: https://www.ldraw.org/cgi-bin/ptdetail.cgi?f=parts/38340.dat
- 38339 Wheel Holder -> 26.12.: on the PT: https://www.ldraw.org/cgi-bin/ptdetail.cgi?f=parts/38339.dat

- Improvement of the old wheels (they are flat on the back not conical)


Brick rounded 3 x 3 - Gerald Lasser - 2019-12-31

I have completed the new air inlet of the X-Wing, the 3 x 3 Brick with a rounded edge. Though I did not find any Design-ID yet

[attachment=4532]

Work is based on these Pictures:
https://s3-us-west-2.amazonaws.com/media.brothers-brick.com/2019/12/LEGO-Star-Wars-75273-Poe-Damerons-X-wing-Fighter-Review-5-1536x806.jpg


60373 - Panel with Arches Tree - Gerald Lasser - 2020-01-01

I am working on this as well, but I cannot find pictures from below...

EDIT: Found the information, including amazing fingernail colours in this video: https://www.youtube.com/watch?v=3q5WjjjTmXc

Uploaded: https://www.ldraw.org/cgi-bin/ptdetail.cgi?f=parts/60373.dat

[attachment=4555]


RE: Parts we are Working on - Part Deux - Gerald Lasser - 2020-01-01

(2019-12-17, 22:51)Gerald Lasser Wrote: ...as the original thread spans now over seven years, I dare to open a new one. The old one is also taking quite some time to load...

So here I go:

New Train Parts:

- 38340 Wheel with Pin -> 26.12.: on the PT: https://www.ldraw.org/cgi-bin/ptdetail.cgi?f=parts/38340.dat
- 38339 Wheel Holder -> 26.12.: on the PT: https://www.ldraw.org/cgi-bin/ptdetail.cgi?f=parts/38339.dat

- Improvement of the old wheels (they are flat on the back not conical)

I put it as "Needs Work" due to the missing details on the back. I modeled them in the meantime, as they are fairly large, but do not really add value for their normal, intended use. See picture
[attachment=4563]
I put them to 48 seg due to their size, I also need to submit the old reworked wheels to Chris


RE: Parts we are Working on - Part Deux - Looking for a proper Name - Gerald Lasser - 2020-01-14

I completed, 62500 and 65196, the books for the Disney Fairy Tale sets. Pending cleanup I am looking for a proper name.

Brickset calls them rather awkwardly:

65196: DESIGN PLATE, BOOK, W/4.85 HOLE, NO. 1
65200: DESIGN PLATE, BOOK, W/ 4.85 HOLE, NO. 2

Looking up Bricklink, there are similar purposed parts in the "Container" category.

What about:
65196: Container, Bookcover 16 x 12 x 2.5 with two Pinholes and Studs on Three Sides
65200: Container, Bookcover 16 x  6 x 1 with four Pinholes and 4 x 16 Studs and Embossed LEGO Logo

Have a look:
[attachment=4659][attachment=4660]


RE: Parts we are Working on - Part Deux - Orion Pobursky - 2020-02-05

I’m current working on the solar panel parts from the new ISS set (21321) and the remaining 3 printed tiles in the Trafalgar Square set (2 1x1 tiles now also found in the Dots sets and the Cat painting). 

When I purchase the ISS I’ll do the remaining printed parts.


RE: Parts we are Working on - Part Deux - Philippe Hurbain - 2020-02-24

Working on 52494 binoculars.


RE: Parts we are Working on - Part Deux - Philippe Hurbain - 2020-02-25

(2020-02-24, 14:44)Philippe Hurbain Wrote: Working on 52494 binoculars.
Done. https://www.ldraw.org/cgi-bin/ptdetail.cgi?f=parts/52494.dat


RE: Parts we are Working on - Part Deux - Gerald Lasser - 2020-02-26

Working on the Pizza/Melon Headgear, 45755*

Opinions:
  • The part is dual mold, but fused together, so two sxx parts will do, or any ideas on the numbering?
  • The part has a bit of "rounded" chamfer along the top and side edges , may be a radius of 0,5 LDU. Do you think it should be modeled?
Parts completed and on the PT!

[attachment=4914]


RE: Parts we are Working on - Part Deux - Philippe Hurbain - 2020-02-26

(2020-02-26, 8:48)Gerald Lasser Wrote: Working on the Pizza/Melon Headgear, 45755*

Opinions:
  • The part is dual mold, but fused together, so two sxx parts will do, or any ideas on the numbering?
  • The part has a bit of "rounded" chamfer along the top and side edges , may be a radius of 0,5 LDU. Do you think it should be modeled?

Sxx will do imho, any chamfer at that size would be overkill!