LDraw.org Discussion Forums
Gerald's Parts and Pieces Thread - Printable Version

+- LDraw.org Discussion Forums (https://forums.ldraw.org)
+-- Forum: Models and Parts (https://forums.ldraw.org/forum-18.html)
+--- Forum: Part Requests (https://forums.ldraw.org/forum-30.html)
+--- Thread: Gerald's Parts and Pieces Thread (/thread-18039.html)

Pages: 1 2 3 4 5 6


Re: Gerald's PPR > Working on 22888 Plate 4 x 8 Round Double - Gerald Lasser - 2016-03-01

I just started this part and while doing it I noticed that Part 30565, "Plate, Round Corner 4 x 4" has an issue that a stud is actually intersecting the inner portion of the wall. Should be changed sometime.


Re: Gerald's PPR > Working on 22888 Plate 4 x 8 Round Double - Stephen - 2016-03-02

If I understand you correctly, it seems that 3 studs intersect the inside curved wall, and part 6003 is also affected the same way.


Re: Gerald's PPR > Working on 22888 Plate 4 x 8 Round Double - Gerald Lasser - 2016-03-02

Exactly, that is the issue with them


Re: Gerald's PPR > Working on 22888 Plate 4 x 8 Round Double - Magnus Forsberg - 2016-03-02

It is missing more than stud cavities. (Note that the LDD mesh is also missing them.)

   


Re: Gerald's PPT > Sandclock (Elves) - Gerald Lasser - 2016-03-04

Set 41137 from the Elves Sets features a nice new part, a sand-clock.
Unfortunately the number on the part is molded so small, I cannot read it...

The part is pretty nice to do with LDPE with a combination of CSG and Pathtruder tools.

I did the sketch with a hi-res sphere, however on the one hand I think it is too much as the file is now (without subfiling to e.g. a quarter) about 2500 lines long... but on the other hand a smooth look is also not bad...
   

Edit:
PS: I am still wondering how all of the pink sand fits into the bottom sphere ;-)


Rollercoaster Track Pieces > 26022 - Gerald Lasser - 2018-03-02

I started the rollercoaster pieces with the short rail.

   

PS: Strange snapshot error...


RE: Rollercoaster Track Pieces > 26022 - Philippe Hurbain - 2018-03-02

Good luck Gerald Wink


RE: Rollercoaster Track Pieces > 26022 - Philippe Hurbain - 2018-04-24

(2018-03-02, 14:36)Gerald Lasser Wrote: I started the rollercoaster pieces with the short rail.
Gerald, what's the status for rollercoaster part modeling? I should get them soon...


RE: Rollercoaster Track Pieces > 26022 - Gerald Lasser - 2018-04-24

(2018-04-24, 14:53)Philippe Hurbain Wrote:
(2018-03-02, 14:36)Gerald Lasser Wrote: I started the rollercoaster pieces with the short rail.
Gerald, what's the status for rollercoaster part modeling? I should get them soon...

I should finish this one in one or two days, did some heads inbetween.


RE: Rollercoaster Track Pieces > 26022 - Gerald Lasser - 2018-04-26

Shall be up tonight, Cond-Lines missing.


.png   26022_Clean_V21.png (Size: 57.36 KB / Downloads: 337)

I just noticed (from pictures) that the 8L and 16L versions do not share the middle sections.

So I might have done some surplus sub-filing. Currently three of them, End, Middle and End-Middle section.