Welcome! Log In Create A New Profile

Advanced
Re: LDCad 1.2 Public Alpha 1
avatarFebruary 24, 2013 02:46PM
Well you could use

0 !LDCAD PATH_SKIN [donCol=16] [donOri=1 0 0 0 1 0 0 0 1] [donPart=x994.dat] [donYSize=100%] [donCen=absCen] [donCenYOfs=0] [donFinScale=fitDon2Seg] [donPlace=deform] [donYAlign=0] [segSize=100%] [segSizeTol=5%] [segsCnt=1] [segsGrp=0] [segsMaxMerge=1]
0 !LDCAD PATH_SKIN [donCol=16] [donOri=1 0 0 0 1 0 0 0 1] [donPart=x993.dat] [donYSize=200%] [donCen=absCen] [donCenYOfs=0] [donFinScale=fitDon2Seg] [donPlace=deform] [donYAlign=0] [segSize=100%] [segSizeTol=5%] [segsCnt=0] [segsGrp=0] [segsMaxMerge=10]
0 !LDCAD PATH_SKIN [donCol=16] [donOri=-1 0 0 0 -1 0 0 0 1] [donPart=x994.dat] [donYSize=100%] [donCen=absCen] [donCenYOfs=0] [donFinScale=fitDon2Seg] [donPlace=deform] [donYAlign=0] [segSize=100%] [segSizeTol=5%] [segsCnt=1] [segsGrp=0] [segsMaxMerge=1]

Instead of the single PATH_SKIN line in your attachment. you will need to adjust the position of the connectors too but the Y segments will deform like all other segments. You could also use the x994 as an extra cap part together with the connector caps. But like you wrote it won't bend that way, but because the limited size of them you won't loose much bending room but it will save on file size.

Or do you mean you don't want to use the x994 part at all, not even for a skin donor? In that case you need to make an alternative for it yourself because one way or another you need a donor for that Y section.

You could (separately) model the donor it self using a path but I don't officially support that in this version, but if you strip away the !LDCAD metas by hand afterwards the resulting part defined by the fallback lines could be used like any other dat/ldr file donor wise.

Hope this helps
SubjectAuthorViewsPosted
LDCad 1.2 Public Alpha 1 Attachments Roland Melkert780February 15, 2013 06:21PM
Re: LDCad 1.2 Public Alpha 1 Travis Cobbs246February 16, 2013 12:21AM
Re: LDCad 1.2 Public Alpha 1 Travis Cobbs218February 16, 2013 12:24AM
Re: LDCad 1.2 Public Alpha 1 Philippe Hurbain225February 16, 2013 08:06AM
Re: LDCad 1.2 Public Alpha 1 Roland Melkert261February 16, 2013 10:17AM
Re: LDCad 1.2 Public Alpha 1 Travis Cobbs224February 16, 2013 07:48PM
Re: LDCad 1.2 Public Alpha 1 Travis Cobbs226February 16, 2013 09:31PM
Re: LDCad 1.2 Public Alpha 1 Philippe Hurbain224February 16, 2013 11:32PM
Re: LDCad 1.2 Public Alpha 1 Travis Cobbs223February 19, 2013 10:06PM
Re: LDCad 1.2 Public Alpha 1 Philippe Hurbain235February 20, 2013 05:25AM
Re: LDCad 1.2 Public Alpha 1 Roland Melkert186February 17, 2013 09:41AM
Re: LDCad 1.2 Public Alpha 1 Ignacio Fernandez Galvan208February 17, 2013 11:30AM
Re: LDCad 1.2 Public Alpha 1 Roland Melkert244February 17, 2013 11:54AM
Re: LDCad 1.2 Public Alpha 1 Ignacio Fernandez Galvan309February 19, 2013 06:05AM
Re: LDCad 1.2 Public Alpha 1 Roland Melkert243February 19, 2013 12:37PM
Re: LDCad 1.2 Public Alpha 1 Ignacio Fernandez Galvan215February 20, 2013 05:05AM
Re: LDCad 1.2 Public Alpha 1 Philippe Hurbain211February 22, 2013 06:48AM
Re: LDCad 1.2 Public Alpha 1 Roland Melkert203February 22, 2013 09:49AM
Re: LDCad 1.2 Public Alpha 1 Philippe Hurbain195February 22, 2013 10:52AM
Re: LDCad 1.2 Public Alpha 1 Ignacio Fernandez Galvan243February 22, 2013 05:37AM
Re: LDCad 1.2 Public Alpha 1 Roland Melkert195February 22, 2013 09:55AM
Re: LDCad 1.2 Public Alpha 1 Ignacio Fernandez Galvan200February 22, 2013 11:04AM
Re: LDCad 1.2 Public Alpha 1 Roland Melkert246February 22, 2013 11:37AM
Re: LDCad 1.2 Public Alpha 1 Ignacio Fernandez Galvan222February 23, 2013 12:21AM
Re: LDCad 1.2 Public Alpha 1 Roland Melkert179February 23, 2013 10:24AM
Re: LDCad 1.2 Public Alpha 1 Ignacio Fernandez Galvan201February 24, 2013 02:35AM
Re: LDCad 1.2 Public Alpha 1 Roland Melkert317February 24, 2013 10:29AM
Re: LDCad 1.2 Public Alpha 1 Attachments Ignacio Fernandez Galvan252February 24, 2013 11:51AM
Re: LDCad 1.2 Public Alpha 1 Roland Melkert216February 24, 2013 02:46PM
Re: LDCad 1.2 Public Alpha 1 Ignacio Fernandez Galvan328February 25, 2013 05:50AM
Re: LDCad 1.2 Public Alpha 1 Roland Melkert342February 25, 2013 03:43PM



Sorry, only registered users may post in this forum.

Click here to login